LONGTEC
  • Home
  • Products
    • Complete Filling Line
    • Standalone Machines
    • Analytical Instruments
    • Weighing Products
    • Level Instruments
  • About Us
  • Case
  • News
  • Service
  • Contact Us
  • 日本語
  • English
  • Español
  • русский язык
  • Français
  • بالعربية
Home  >  Products  >  Weighing Products  >  LT8100-EX Explosion-Proof Touch Terminal
lt8100-ex-06-main-white.webp
lt8100-ex-01-cover.webp
lt8100-ex-02-dual-view-a.webp
lt8100-ex-03-dual-view-b.webp
lt8100-ex-04-key-specs.webp
lt8100-ex-05-typical-applications.webp
lt8100-ex-07-front-panel.webp
lt8100-ex-06-main-white.webp
lt8100-ex-01-cover.webp
lt8100-ex-02-dual-view-a.webp
lt8100-ex-03-dual-view-b.webp
lt8100-ex-04-key-specs.webp
lt8100-ex-05-typical-applications.webp
lt8100-ex-07-front-panel.webp

LT8100-EX Explosion-Proof Touch Terminal

The LT8100-EX is an explosion-proof human-machine interface for classified areas, where an ordinary panel cannot be installed. It is a touch terminal built around a 32-bit RISC Cortex-A8 processor at 600 MHz, with a 10 inch TFT at 1024 x 600 or a 12 inch TFT at 1024 x 768, an LED backlight rated above 50,000 hours, a four-wire resistive touch panel and a built-in real-time clock. The processor, the 128 MB of flash and the 128 or 256 MB of RAM are enough to run a full operator interface with trends, recipes and alarms, and the panel is programmed in EasyBuilder Pro, so an existing project can be ported without rewriting it. The supply is 24 V DC with a ±20 % tolerance and the consumption is 650 mA at 24 V, which is modest for a panel of this size, and the enclosure is built for explosion-proof service with non-standard ODM customisation available.

Email: marketing@longtec.com

Tel: 00864007808806

Whatsapp: 8618269775217

REQUEST A QUOTE
Main Functions
Applications
Spec Sheet
FAQ
Main Functions

· Explosion-proof touch terminal for classified areas, replacing a general-purpose panel where the zone does not allow one.

· 10 inch 1024 x 600 or 12 inch 1024 x 768 TFT with an LED backlight rated above 50,000 hours.

· 32-bit RISC Cortex-A8 at 600 MHz with 128 MB flash and 128 or 256 MB RAM, enough for trends, recipes and alarms.

· Four-wire resistive touch panel with ±2 % positional accuracy, which works with a gloved finger.

· 24 V DC supply with ±20 % tolerance and 650 mA consumption, programmed in EasyBuilder Pro.

· Built-in real-time clock and ODM customisation for non-standard panel sizes or interfaces.

Applications

The LT8100-EX is used as the operator interface in hazardous areas of chemical and petrochemical plants, paint and coating works, solvent-handling areas, grain and starch plants with combustible dust, pharmaceutical facilities handling solvents, and any process area where an operator needs a screen but the zone does not allow a general-purpose panel. It typically displays a batching or weighing sequence, a filling line, a reactor or a tank farm, and replaces a local push-button station with a graphical interface that can show trends and alarms.

Spec Sheet

LT8100-EX spec table

FAQ

What Ex rating does it carry?

The panel is built for explosion-proof service and the Ex marking, certificate number and temperature class are stated on the nameplate of each unit. State the zone, the gas or dust group and the temperature class when ordering so the enclosure and the certification match the area.

Can I reuse an existing EasyBuilder project?

Yes. The panel is programmed in EasyBuilder Pro, which is the standard environment for this class of HMI, so an existing project can be opened, resized for the 10 or 12 inch screen and downloaded. The address mapping to the PLC has to be checked against the controller used in the hazardous area.

Is a resistive touch screen suitable for plant use?

Yes, and it is the right choice here: a four-wire resistive panel works with a gloved finger and with a stylus, and it does not need the optical clarity of a capacitive panel, which matters when the front is behind an explosion-proof window.

What supply does it need?

24 V DC with a ±20 % tolerance, drawing 650 mA. In a hazardous area the supply has to come through a suitable barrier or from an approved source in the same zone; the panel itself is the protected equipment.

Can the panel be customised?

Yes. Non-standard ODM customisation is offered, which covers panel size, interface configuration and branding. For a machine builder that ships into a classified area, that is often the difference between a standard panel and a fitted one.

Related Products

TR200H Analog Weighing Signal TransmitterTR200H Analog Weighing Signal Transmitter
TR700L Digital Weight TransmitterTR700L Digital Weight Transmitter
TR700C Multi-Material Batching ControllerTR700C Multi-Material Batching Controller
TR700-LF Loss-in-Weight Feeding Control ModuleTR700-LF Loss-in-Weight Feeding Control Module
TR700-BC Belt-Scale Batching Control ModuleTR700-BC Belt-Scale Batching Control Module
TR700M Intelligent Multi-Channel Weight TransmitterTR700M Intelligent Multi-Channel Weight Transmitter
LONGTEC

Solutions & Support

We go the extra mile to thoroughly analyze each project and deliver tailored business solutions that meet your specific requirements.

  • TR200H Analog Weighing Signal Transmitter
  • TR700L Digital Weight Transmitter
  • UNI800S Digital Weight Transmitter
  • UNI900D3 Digital Weighing Instrument
  • IM2000 Online Infrared Moisture Analyzer
  • Company Profile
  • Why Choose Us 
  • Certificates
  • Company Partners
  • Privacy Policy
  • Tel: 400-7808-806
  • E-mail:marketing@longtec.com
  • Address:No. 3 Jinliang Road, Hongqi Town, Jinwan District, Zhuhai City, Guangdong Province, China

Copyright © 2026 singoo Technical supp

  • Whatsapp

  • Inquiry

Contact US

×